Home > Painting & Refinishing > Sealants & Adhesives > Epoxy Products
Click on image to see ordering information.
Sort By:
Page of 1
Evercoat 100643 Everfix Epoxy Resin Quart J-B Weld 8276 Kwik Weld 2 oz. J-B Weld 8277 Water Weld 2 oz.
Evercoat 100643 Everfix Epoxy Resin Quart
List Price: $89.91
Our Price: $69.99
J-B Weld 8276 Kwik Weld 2 oz.
List Price: $7.99
Our Price: $6.99
J-B Weld 8277 Water Weld 2 oz.
List Price: $8.99
Our Price: $7.99
  • 50/50 mix, all purpose resin for fiberglassing, molding, laminating, repairing or where superior adhesion is required.
  • Used on aluminum, steel, fiberglass, close-grained hardwoods and styrofoam.
  • Packaged in kits of equal portions of resin and hardener.
  • Not as strong or as heat-resistant as the original J-B WELD.
  • Like metal, it can be formed, drilled, ground, tapped, machined, filled, sanded, and painted.
  • It stays pliable for about 2 minutes after mixing, sets in just 4 minutes, and cures fully in 4 hours.
  • Waterproof and chemical resistant.
  • Before it sets, you can clean up with soap and water. (print instruction sheet).
  • Will plug or seal practically anything that leaks.
  • It will patch holes and cracks, and mend almost anything that is broken.
  • It is excellent for rebuilding or fabricating parts, and as an all-purpose adhesive for metals, wood, fiberglass, masonry, ceramics, PVC and ABS.
  • Permanently repair holes, gouges, cuts ... even seals rot in fiberglass and wood.
  • Cures under water.
  • Safe for use on lines carrying potable water.
  • Can be applied under water; surfaces to be repaired do not need to be clean and dry.
Boatlife Git Rot - 1064 - Pint Protective Coating Co. PC-Marine Putty ITW Philadelphia Resins 3011C Marine Tex White 2 oz.
Boatlife Git Rot - 1064 - Pint
List Price: $56.83
Our Price: $51.15
Protective Coating Co. PC-Marine Putty
List Price: $5.95
Our Price: $4.99
ITW Philadelphia Resins 3011C Marine Tex White 2 oz.
List Price: $23.96
Our Price: $20.99
  • Two-part liquid epoxy saturates and restores original strength to wood by penetrating the rot.
  • Not necessary to remove loose rotted fibers.
  • Wood must be dry.
  • Apply by injecting into wood.
  • Will soak into wood by capillary action.
  • One-half hour pot life after mixing.
  • Cures overnight. Sandable and paintable, can be drilled and screwed.
  • Compatible with fiberglass resins, epoxies and most sealants.
  • Great for transoms, stringers and cabin roof rot in both fiberglass and wood boats.
  • Hand moldable epoxy putty that is especially designed for emergency repairs where time is of the essence.
  • Work time: 20 min. Cure time: 60 min.
  • High-strength epoxy repair compound designed for filling, bonding and rebuilding wood, fiberglass, ceramic, glass, metal, masonry and many plastics.
  • Easy-to-apply paste makes permanent repairs to hulls, decks, and equipment, including exhaust lines, outdrives, tanks, piping and stringers.
  • Can be used to fill gouges in wood and fiberglass, making repaired area stronger than before.
  • Allows sufficient working time for complex repairs.
  • Bonds dissimilar metals without galvanic corrosion.
  • Can be drilled and tapped. Paintable after cure.
ITW Philadelphia Resins 3001C Marine Tex 2 oz. Gray ITW Philadelphia Resins 3013C Marine Tex White 14 oz. ITW Philadelphia Resins 3015C Marine Tex White Quart
ITW Philadelphia Resins 3001C Marine Tex 2 oz. Gray
List Price: $22.12
Our Price: $19.91
ITW Philadelphia Resins 3013C Marine Tex White 14 oz.
List Price: $59.02
Our Price: $46.99
ITW Philadelphia Resins 3015C Marine Tex White Quart
List Price: $151.84
Our Price: $136.66
  • High-strength epoxy repair compound designed for filling, bonding and rebuilding wood, fiberglass, ceramic, glass, metal, masonry and many plastics.
  • Easy-to-apply paste makes permanent repairs to hulls, decks, and equipment, including exhaust lines, outdrives, tanks, piping and stringers.
  • Can be used to fill gouges in wood and fiberglass, making repaired area stronger than before.
  • Allows sufficient working time for complex repairs.
  • Bonds dissimilar metals without galvanic corrosion.
  • Can be drilled and tapped. Paintable after cure.
  • High-strength epoxy repair compound designed for filling, bonding and rebuilding wood, fiberglass, ceramic, glass, metal, masonry and many plastics.
  • Easy-to-apply paste makes permanent repairs to hulls, decks, and equipment, including exhaust lines, outdrives, tanks, piping and stringers.
  • Can be used to fill gouges in wood and fiberglass, making repaired area stronger than before.
  • Allows sufficient working time for complex repairs.
  • Bonds dissimilar metals without galvanic corrosion.
  • Can be drilled and tapped. Paintable after cure.
  • High-strength epoxy repair compound designed for filling, bonding and rebuilding wood, fiberglass, ceramic, glass, metal, masonry and many plastics.
  • Easy-to-apply paste makes permanent repairs to hulls, decks, and equipment, including exhaust lines, outdrives, tanks, piping and stringers.
  • Can be used to fill gouges in wood and fiberglass, making repaired area stronger than before.
  • Allows sufficient working time for complex repairs.
  • Bonds dissimilar metals without galvanic corrosion.
  • Can be drilled and tapped. Paintable after cure.
ITW Philadelphia Resins 3003C Marine Tex 14 oz. Gray Gluvit™ Waterproof Epoxy Sealer Quart Kit RM330C 3018C Rapid Set Marine Tex 2 oz.
ITW Philadelphia Resins 3003C Marine Tex 14 oz. Gray
List Price: $59.02
Our Price: $46.99
Gluvit Waterproof Epoxy Sealer Quart Kit RM330C
List Price: $84.00
Our Price: $64.99
3018C Rapid Set Marine Tex 2 oz.
List Price: $17.64
Our Price: $15.88
  • High-strength epoxy repair compound designed for filling, bonding and rebuilding wood, fiberglass, ceramic, glass, metal, masonry and many plastics.
  • Easy-to-apply paste makes permanent repairs to hulls, decks, and equipment, including exhaust lines, outdrives, tanks, piping and stringers.
  • Can be used to fill gouges in wood and fiberglass, making repaired area stronger than before.
  • Allows sufficient working time for complex repairs.
  • Bonds dissimilar metals without galvanic corrosion.
  • Can be drilled and tapped. Paintable after cure.
Seals and protects hulls and decks. Provides superior protection for fiberglass, wood, aluminum, and steel. Seals leaky seams and rivets in aluminum hulls, and leaks around fiberglass cabins or decks. Hard protective coating flexes with hull movements to bridge and seal hairline cracks.
  • Waterproof epoxy paste is a convenient 1:1 mix for emergency and permanent repairs.
  • Superior bond fills cracks and voids in fiberglass, steel, aluminum, wood, cast iron and many hard plastics.
  • Paintable repair can be drilled, tapped and sanded.
  • Excellent for quick machinery and mechanical repairs to get back underway with minimum downtime.
  • Secures hardware and loose fasteners.
  • Cures in one hour at 72°F.
Starbrite 93401 Epoxy Syringe Clear 1 OZ. J-B Weld 8772 Marine Weld Epoxy 2 oz. J-B Weld ClearWeld Epoxy Syringe 25 ml 50112
Starbrite 93401 Epoxy Syringe Clear 1 OZ.
List Price: $12.15
Our Price: $10.45
J-B Weld 8772 Marine Weld Epoxy 2 oz.
List Price: $7.99
Our Price: $6.99
J-B Weld ClearWeld Epoxy Syringe 25 ml 50112
List Price: $7.99
Our Price: $6.99
  • 5 Minute Cure Clear Epoxy
  • Convenient self-metering syringe applicator
  • Bonds fiberglass, rubber, hard plastic, glass, fabric, ceramic, and metal
  • Fills cracks and holes, mounts components, seals seams.
  • Resists most liquids.
  • Crystal clear appearance after curing.
  • Permanent strength up to 3400 PSI.
  • Syringe provides easy even mix of hardener and epoxy for fast application.
  • 2-part product cures as strong as steel, and is water- and weather-proof.
  • Can be formed, drilled, ground, tapped, machined, filled, sanded, and painted.
  • It stays pliable for about 30 minutes after mixing, sets in 4-6 hours, and cures fully in 15-24 hours.
  • Before it sets, clean up with soap and water.
ClearWeld is a quick setting, multipurpose two part epoxy that provides a strong and lasting bond on most surfaces including tile, most plastics, ceramic, glass, wood and metal. ClearWeld is designed to cure with a clear, transparent bond when used at thicknesses of less than 15 mil. ClearWeld has a 1:1 mixing ratio, sets in 5 minutes and will fully cure overnight. With a tensile strength of 3200 PSI, ClearWeld sets to a hard, permanent bond.
Sets in 15 minutes. Cures in 30 minutes. If temperature is below 40ºF, then set time is longer.
Protective Coating Co. PC-11 White Epoxy Paste 1/2 lb. Can Pettit EZ-Tex Rapid Cure Putty - 7200 - 2 Oz. Pettit EZ-Fair Lightweight Two-Part Epoy Fairing Compound - 7050CRT - 6.5 Oz. Cartridge
Pettit EZ-Tex Rapid Cure Putty - 7200 - 2 Oz.
List Price: $18.80
Our Price: $14.99
  • Heavy duty white epoxy paste can be applied to a dry, wet or underwater surface and will cure to an off white color.
  • Working time of over 1/2 hour.
  • Excellent chemical resistance to mild acids, caustics, detergents, gasoline, fuel oil, salt and fresh water.
  • Will not bond to Teflon, polyethylene and some soft flexible plastics.
  • Easy to use 1:1 mix ratio repair compound for cracks, gouges, voids and holes
  • High strength formula makes repairs permanent
  • 100% waterproof when cured
  • Can be used above and below the waterline
  • Will not sag, shrink or run
  • Available in 4oz and 16oz

EZ-Tex is an easy to use marine epoxy repair compound for use where a high strength, waterproof, permanent repair is needed. This unique formula creates a tenacious bond to most surfaces. Its buttery consistency will not sag or shrink and is excellent for filling cracks, gouges and voids. A 1:1 ratio makes mixing easy. EZ-Tex can be sanded, drilled, tapped, sawed and painted once cured.
      • For fairing, filling, and patching
      • Fast-cure formula allows for quick recoats
      • Can be easily painted
      • Waterproof when cured
      • Use above or below the waterline
      • Excellent chemical resistance

        EZ-Fair Epoxy Fairing Compound 7050 is a lightweight, two-part epoxy putty designed for filling and smoothing surface imperfections above and below the waterline. The special resins used in EZ-Fair impart a high degree of water and chemical resistance to the product, making it an integral part of the Pettit Gelcoat Blister Repair System. In addition, EZ-Fair is the product of choice for fairing metal keels or any underwater surface. Use it for leveling uneven surfaces, filling gouges, scratches, or other damage on fiberglass, wood or metal surfaces. It’s excellent chemical and water resistance make it the ideal choice for repairing blistered gelcoat in an osmotic blister repair system. EZ-Fair is non-sagging and non-shrinking and sands to a smooth finish. The quick-cure formula allows for multiple coats to be applied and sanded in a single day.
Pettit Flexpoxy Flexible Repair and Construction Epoxy - 7076 - Pettit Splash Zone Multi-Purpose Two Part Epoxy Repair Compound - A788QT - 2 Pint Set Pettit EZ-Fair Lightweight Two-Part Epoy Fairing Compound - 7050QT - Quart
  • Will not sag, run, or shrink
  • For large or small repairs
  • Remains flexible
  • Offers superior bonding
  • Can be molded and shaped
  • Use above and below the waterline
  • Can be machined, sanded, drilled and tapped
  • Low odor formula


Flexpoxy 7076 is a two-part epoxy resin that does not sag, run, or shrink. Its thick formula allows it to fill large cavities in a single application. When cured, it remains flexible making it ideal for environments that require flex such as keel joint repairs. Flexpoxy creates a superior bond to all epoxies, polyester resins, metals and wood. It can be sanded, machined, cut, filed, planed, drilled, tapped, or nailed making it perfect for filling, filleting, forming, fairing, and fastening. This low odor formula is resistant to chemicals and is safe to use above and below the waterline. Flexpoxy can be molded and shaped during application and is easily tinted with paints and stains. Flexpoxy can be over coated by most paints and stains.

      • So versatile, it has been called “The duct tape of the marine world”
      • Use above or below waterline
      • Excellent for underwater repairs
      • Produces a rock-hard protective surface
      • Two-part multi-purpose epoxy patching and repair compound
      • Provides excellent protection against corrosion of metals
      • Stops erosion and deterioration of concrete or wood

      • A-788 Splash Zone is an extremely hard, abrasion and impact resistant, two-part epoxy patching compound. It applies like putty to seal, fill, patch, or re-build aluminum, wood, concrete, fiberglass, and steel. It can be applied in or out of water to repair boat hulls, buoys, seawalls, docks, bridge abutments, and more. Splash Zone provides excellent protection against corrosion of metals and erosion and deterioration of concrete or wood. Splash Zone’s rock-hard surface can be drilled, tapped, or machined. Recommended for patching and repairing damaged underwater surfaces. Not for use in potable water.

      • For fairing, filling, and patching
      • Fast-cure formula allows for quick recoats
      • Can be easily painted
      • Waterproof when cured
      • Use above or below the waterline
      • Excellent chemical resistance

        EZ-Fair Epoxy Fairing Compound 7050 is a lightweight, two-part epoxy putty designed for filling and smoothing surface imperfections above and below the waterline. The special resins used in EZ-Fair impart a high degree of water and chemical resistance to the product, making it an integral part of the Pettit Gelcoat Blister Repair System. In addition, EZ-Fair is the product of choice for fairing metal keels or any underwater surface. Use it for leveling uneven surfaces, filling gouges, scratches, or other damage on fiberglass, wood or metal surfaces. It’s excellent chemical and water resistance make it the ideal choice for repairing blistered gelcoat in an osmotic blister repair system. EZ-Fair is non-sagging and non-shrinking and sands to a smooth finish. The quick-cure formula allows for multiple coats to be applied and sanded in a single day.
Pettit Splash Zone Multi-Purpose Two Part Epoxy Repair Compound - A788HGS - 1/2 Gallon Set Pettit Splash Zone Multi-Purpose Two Part Epoxy Repair Compound - A7882GS - 2 Gallon Set
      • So versatile, it has been called “The duct tape of the marine world”
      • Use above or below waterline
      • Excellent for underwater repairs
      • Produces a rock-hard protective surface
      • Two-part multi-purpose epoxy patching and repair compound
      • Provides excellent protection against corrosion of metals
      • Stops erosion and deterioration of concrete or wood

      • A-788 Splash Zone is an extremely hard, abrasion and impact resistant, two-part epoxy patching compound. It applies like putty to seal, fill, patch, or re-build aluminum, wood, concrete, fiberglass, and steel. It can be applied in or out of water to repair boat hulls, buoys, seawalls, docks, bridge abutments, and more. Splash Zone provides excellent protection against corrosion of metals and erosion and deterioration of concrete or wood. Splash Zone’s rock-hard surface can be drilled, tapped, or machined. Recommended for patching and repairing damaged underwater surfaces. Not for use in potable water.

      • So versatile, it has been called “The duct tape of the marine world”
      • Use above or below waterline
      • Excellent for underwater repairs
      • Produces a rock-hard protective surface
      • Two-part multi-purpose epoxy patching and repair compound
      • Provides excellent protection against corrosion of metals
      • Stops erosion and deterioration of concrete or wood

      • A-788 Splash Zone is an extremely hard, abrasion and impact resistant, two-part epoxy patching compound. It applies like putty to seal, fill, patch, or re-build aluminum, wood, concrete, fiberglass, and steel. It can be applied in or out of water to repair boat hulls, buoys, seawalls, docks, bridge abutments, and more. Splash Zone provides excellent protection against corrosion of metals and erosion and deterioration of concrete or wood. Splash Zone’s rock-hard surface can be drilled, tapped, or machined. Recommended for patching and repairing damaged underwater surfaces. Not for use in potable water.